Login | Register
Kazakh National Agrarian Research University ISSN 2304-3334 (Print)  ·  ISSN 2304-3334 (Online)
submit an article
Menu
submit an article
AGRICULTURE MECHANIZATION AND ELECTRIFICATION

JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE

Zhasulan Mustafin 1 , Yesenali Kaspakov 1 , Arman Rustembayev 1 , Yerbol Sarkynov 2 , Mizambek Zhetpeisov 2 , Zhandos Zhumagulov 2

1 S.Seifullin Kazakh Agrotechnical Research University; 2 Kazakh National Agrarian Research University

doi.org/10.37884/1-2025/40 pp. 371-381 Admitted 21.01.2025 Published 30.03.2025

Abstract

Investigation of the Diameter of Toothed Drums Installed on the Crusher During the Crushing of All Grain Crops, Rotational Speed, and the Gap Between the Two Drums.

Geometric parameters of the toothed drum that influence the grain crops during the crushing process were determined. It was established that energy consumption is reduced when crushing with toothed drums. As a result of theoretical research, the performance and speed of the grinder were defined. During the investigation, it was noted that the two counter-rotating drums should rotate at different speeds—one faster and another slower.

Furthermore, by considering the entry of the drum teeth into the grains and the arrangement of the grains along the length of the drum, the power required for crushing was determined, which indicated that the accuracy of the expression is sufficient for engineering equations. The power expended during the crushing process at various rotational frequency intervals was defined in this study. Additionally, theoretical values of the power spent on the crushing process at the rotational frequencies of the toothed drums were established.

A comparison of these theoretical power values with the experimental values obtained during the research was conducted. In justifying the design and technological development of the crusher, the diameter of the toothed drums was chosen based on the results of the theoretical studies.

Crusher, oothed drum, сrushing process, cereal crops, power, productivity, degree of grinding.

01 Introduction

The full text of the article is available for download in PDF format on the right panel.

02 References

  1. 1 Кочетков А.С., Некрашевич В.Ф. Измельчение зерновых культур на вальцевой плющилке. Аграрная наука как основа продовольственной безопасности региона: Материалы 66-й международной научно-практической конференции 14 мая 2015 года. Рязань: Издательство Рязанского государственного агротехнологического университета, 2015. – Часть 2. - 230 с.
  2. 2 Кочетков А.С., Некрашевич В.Ф. Особенности рабочего процесса вальцевой плющилки. Аграрная наука как основа продовольственной безопасности региона: Материалы 66-й международной научно-практической конференции 14 мая 2015 года. Рязань: Издательство Рязанского государственного агротехнологического университета, 2015. – Часть 2. – 230 с.
  3. 3 Аnіmаl Fееd Sсіеnсеаnd Тесһnоlоgу. Рublіsһеd bу Еlsеvіеr, №200. Fеbruаrу 2015. Р. 1-120.
  4. 4 «Нayкa и Mиp» – 0.325 (Glоbаl Іmрасt Fаctоr 2013, Aвcтpaлия).
  5. 5 Corol D, Ravel C, Raksegi M, et al. Effects of genotype and environment on the contents of betaine, choline, and trigonelline in cereal grains. Journal of Agricultural and Food Chemistry. – 2012. - Р. 5471-5481.
  6. 6 Д.Н.Оразахын, Т.Абилжанулы, О.А.Сауытов, Ф.Кумхала, Е.Б.Рахымбаев. Жүгері сабақтарының физика-механикалық қасиеттерін және комбайнның параметрлерін анықтау. Научный журнал «Ізденістер, нәтижелер – Исследования, результаты». №2 (102) 2024, - Алматы, – С. 461-472. DOI: https://doi.org/10.37884/1-101-2024
  7. 7 Mustafin Zh.Zh. Preliminary cuttering of a corn cob for preparation of fodder. International Journal of Mechanical Engineering and Technology (IJMET) Volume 10. Issue 03. March 2019. P. 1636-1644.
  8. 8 Муcтaфин Ж.Ж. Жүгepi coбығын aлдын-aлa ұcaқтaуғa apнaлғaн қoндыpғығa кepeктi қуaтын aнықтaу. Жapшы. Ғылыми-тeopиялық жәнe пpaктикaлық жуpнaлы. №12. - 2009ж. – Б.66-69.
  9. 9 Аnіmаl Fееd Sсіеnсе аnd Тесһnоlоgу. Рublіsһеd bу Еlsеvіеr, №200 Fеbruаrу 2015 р1-120.
  10. 10 П. А. Савиных, В. А. Казаков. Разработка и исследования питающего устройства плющилки зерна. Пермский аграрный вестник №2 (22) 2018. - С 22-24.
  11. 11 Казаков В. А., Мошонкин А. М. Усовершенствование питающего устройства двухступенчатой плющилки зерна // Аграрная наука в условиях модернизации и инновационного развития АПК России: Сб. материалов Всероссийской научно-методической конференции с международным участием, посвящается 100-летию академика Д. К. Беляева. Т. 3. Иваново: ФГБОУ ВО Ивановская ГСХА, 2017. С. 75-79.
  12. 12 Савиных П. А., Казаков В. А. Новая плющилка для производства зерновых кормов // Вестник Марийского государственного университета. 2015. № 2 (2). С. 44-48
  13. 13 Баймаханов К. Мал азық дайындап берудің агрегаты. Жәңгір хан атындағы Батыс Қазақстан аграрлық-техникалық университетінің ғылыми-практикалық журналы. Ғылым және білім. 2-бөлім. № 4-2 (77) 2024. 189-199 бет. https://DOI.org/10.52578/2305-9397-2024-4-2-189-199
  14. 14 Полищук Ю.В., Дерепаскин А.И., Лаптев Н.В., Комаров А.П. Подборщик плющилка – техническое средство для повышения производительности и качества на загатовке кормов. Научное обеспечение животноводства Сибири: мат-лы III Междунар. науч.практ. конф. / Составители Л.В. Ефимова, Т.В. Зазнобина; КрасНИИЖ ФИЦ КНЦ СО РАН. – Красноярск, 2019. – 412 с.
  15. 15 Т. Abilzhanuly, D. Т. Аbilzhanov, А. S. Аlshurina. Cchecking of resource-saving technologies for making roughage in the crushed form at the picking up hay from the swath under the farm conditions. Bulletin of national academy of sciences of the Republic of Kazakhstan. ISSN 1991-3494 Volume 3, Number 367 (2017), P. 161-166.
  16. 16 Размыслович Д.П.,Трофимович Л.И. Загатовка кормов из бобовых трав с использованием вальцового рекондиционера. Научно-технический прогресс в сельскохозяйственном производстве. Аграрная наука – сельскхозяйственному производству Сибири, Казахстана, Монголии, Белоруси и Болгарии. Минск, 19-21 октября 2016 года. 164-168 с.

Citation Links

[1]2025. JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE. Izdenister natigeler. 1 (105) (Mar. 2025), 371–381. DOI:https://doi.org/10.37884/1-2025/40.
(1)JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE. Izdenister natigeler 2025, No. 1 (105), 371-381. https://doi.org/10.37884/1-2025/40.
JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE. (2025). Izdenister Natigeler, 1 (105), 371-381. https://doi.org/10.37884/1-2025/40
JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE. Izdenister natigeler, [S. l.], n. 1 (105), p. 371–381, 2025. DOI: 10.37884/1-2025/40. Disponível em: https://natsus.kaznaru.edu.kz/index.php/research/article/view/827. Acesso em: 15 sep. 2026.
“JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE”. 2025. Izdenister Natigeler, no. 1 (105) (March): 371-81. https://doi.org/10.37884/1-2025/40.
“JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE” (2025) Izdenister natigeler, (1 (105), pp. 371–381. doi:10.37884/1-2025/40.
[1]“JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE”, Izdenister natigeler, no. 1 (105), pp. 371–381, Mar. 2025, doi: 10.37884/1-2025/40.
“JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE”. Izdenister Natigeler, no. 1 (105), Mar. 2025, pp. 371-8, https://doi.org/10.37884/1-2025/40.
“JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE”. Izdenister natigeler, no. 1 (105) (March 30, 2025): 371–381. Accessed September 15, 2026. https://natsus.kaznaru.edu.kz/index.php/research/article/view/827.
1.JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE. Izdenister natigeler [Internet]. 2025 Mar. 30 [cited 2026 Sep. 15];(1 (105):371-8. Available from: https://natsus.kaznaru.edu.kz/index.php/research/article/view/827
1.JUSTIFICATION OF THE PARAMETERS OF THE TOOTHED DRUM THRESHING MACHINE. Izdenister natigeler. 2025;(1 (105):371-381. doi:10.37884/1-2025/40